Anti-Sleep Alarm Driver Fatigue Monitor
►It features concise, detecting driver fatigue state and remind
driver careless driving
►The driver state detection precision, the accuracy of alarm is
close to 99%
►The product is designed with a smooth appearance structure to
protect the driver
►This product normal working conditions are not affected by
external light source
►It can work in the vast majority of private cars, and adapt to
most climatic conditions
►Easy to install in vehicle, it only need make the product look up
to driver face
Product Technical parameters:
Recommended installation position: above the instrument panel, the
central position of the steering wheel
Installation distance: Max150cm (recommended distance: 45cm~150cm)
►Determine the installation location and remove foreign objects;
►Composite host and bracket;
►Open the bottom double-side adhesive sticker and paste in the
right position of the bridge;
►Connect the power;
►Adjust the camera lens position so that it can effectively
identify the driver's view.
In the case of navigation, connect the AV line to the host AV port
and the navigation AV port and adjust according to the driver's
face that appears in the navigation screen
Fatigue Driving Warning
It monitors the driver's facial state, mouth and eyes in real time;
Remind the driver to stop and rest when the driver is tired;
t makes a serial urgent voice when the driver in the different
he urgent voice is increase alarm level according to different
Careless Driving Warning:
It continued to monitor the steering movement of driver’s head;
Remind the driver Attention Road when the head continues to tilt
It makes a serial voice when the driver always glance right and
This function helps more than half of drivers have a habit of
|Video||Sensor||1/3“ CMOS 940nm IR sensor|
|Effective Pixels||CVBS 700TVL (PAL:720×576; NTSC:720×480)|
|Signal Standard||Voltage:1.0Vp-p, Input / Output Impedance: 75Ω|
|Video Standard||PAL Mode, NTSC Mode, Before factory selected|
|Image Transfer Rate||25 Frame / Sec PAL, 30 Frame / Sec NTSC|
|Low Light Sensitivity||best-in-class of 4500 mV / Lux-Sec|
|Infrared LED||940nm far-infrared invisible light|
|View Angle||Horizontal 60degree, Vertical 30degree|
|Warning and Reminding||System Base||Vehicle start displacement / Vehicle launch by the engine start|
|Fatigue Driving Warning||A series alert sound, A series alert whistles, A series alert bell|
|Careless Driving Warning||A series alert sound, A series alert whistles|
|Indicator Light||Middle LED On Red||The left Red LED on when there have detected the driver|
|Middle LED On Green||The right Green LED on when BF-CB1 have calibrated of driver face
|Interface||Power||DC 12V, Protect the vehicle battery, Max power requirements: 4.0
|Video||Aviation interface, Voltage:1.0Vp-p, Input / Output Impedance:75 Ω|
|Audio||Aviation interface, Voltage:2.0Vp-p, Input / Output Impedance:4.7KΩ
/ 1.0 KΩ|
|Serial Port||1Ch RS232, The baud rate is 20Kbps, +3~+15V is 0, -3~-15V is 1|
|Alarm I/O output||1Ch RS232 conversions Alarm I/O output|
|Installation||Installation Site||Above the instrument panel, the central position of the steering
|Installation Distance||Max75cm (The recommended range is 45~75cm)|
|Working Distance||From camera to driver face distance best is 45cm~75cm|
|Size & Weight||Mainframe Size||L×W×H: 55×102×58 mm|
|Package Size||L×W×H: 100×150×80 mm|
Graphical User interface(OSD menu)
User /Admin password
IR remote control
4-ch video composite input
1-ch composite output
Single/ 4-ch video
H.264 Main profile
PAL:100f at D1/s, NTSC: 120f at D1/s
4-ch audio input
1-ch audio output
Audio & Video sync Recording
Support IP call and analog voice call
Image processing & storage
Image format mode
Video stream Standard
CIF: 1536Kbps ~ 128Kbps,4 levels optional.
Highest:0 level; Lowest: 3 level
HD1: 2048Kbps ~ 512Kbps,4 levels optional.
Highest:0 level; Lowest: 3 level
D1: 4Mbps ~ 1Mbps,4 levels optional.
Highest:0 level; Lowest: 3 level
Built-in a SATA HDD, support HDD Max 2TB;
And built-in a SD card, Support SD card Max 128GB;
8 alarm input, below 4V is low level alarm, above 4V are high level
2 alarm output, output high level:12V
Support 3-RS485 interface
Support 1-RS232 interface
Support RJ45 interface external 802.11b/g
Include 2 USB interfaces,1 USB interface connect with external
Vehicle Black data
box,another USB interface to upgrade software and copy data.
Support Audio and Video output
Built in acceleration G-Sensor
GPS module. GPS Graph and GPS speed can be read in coding
flow, and can be uploaded via wireless
WCDMA / EVDO/HSPA(TD-SCDMA) module
RJ45 interface external WIFI, IEEE802.11n, Up to 300 Mbps physical
transfer speed, satisfy huge data Transmission;
PAS(Playback Analysis Software)
Playback Recording on PC, and analyze the vehicle recording
CMS(Center Management Software)
Center management software to meet Video preview, upload and
central command and parameters configuration, etc.
U-disk upgrade directly.
Playback all video file and GPS tracking(Playback Analysis
Q: What can I do when I found a problem with the product, but I can
not solve it by myself?
A: Take note of the model and software version number, then submit
a detailed description of the problem to the technical supporting
engineers to analyze; the more detailed you have submitted, the
more convenient for us to analysize.
Q: How about when there is no video output from the vehicle host
A: 1.Check the host’s turn-on status, if only a blue light on, it
means the host is in standby status and has not been started up
yet, meanwhile check whether the host’s power cords red &
yellow cords are in power supply status or not, if only one cord is
supplying power, the device is unable to start up.
2.Check the power supply status of display screen, as well as check
whether the display video has been switched to AV status.
3 Check the connecting status between the host’s video output cable
and display screen.
4 check whether the lock status of the host’s LOCK, it must be
locked before normal starting up.
Q: How to do when the car host video input interface is different
from the camera output interface?
A: The car uses 4PIN type while camera uses BNC or aviation head
type, if not in correspondence, please use conversion head for
connection or wiring based on standard corresponding according to
the cable sequence defined by the car host.
Q: How to do when the device does not conduct video recording after
it is turned on and SD card has already been installed?
A: 1.Check whether the SD card has been formatted or not after
installation, because unformatted SD card cannot be used. Enter
System Menu - System Tools - Device Format to format the newly
installed SD card;
2. Check to see whether video channel is closed or not, whether set
a timer recording or not, it will not take video when it is not
within the video recording time period.
3.Check the SD card inserting status and whether the SD light on
front panel is on or not.
Q: The video file is missing or there is no video file within a
certain period of time, how to do?
A: 1. Determine the time period by analyzing the final video file
before missing and the first video file after recovery.
2. Confirm whether the host is not on during that period of time,
such as when the driver halfway parking, loading and unloading
goods while the host is not set by video delay.
Q: When car PTZ cannot be controlled, it cannot rotate up and down,
how to do?
A: Check whether PTZ protocols and baud rate are set correct,
address codes are corresponding or not, whether have selected to
maximize the video of the channel when control the PTZ, for
example, when control the second channel, it must maximize the
screen of the second channel image to control it.GPS-related issues
Q: GPS module exists but no coordinate information?
A: 1.Check whether GPS module exists, if it does not exist, check
whether the hardware is installed or in a good contact.
2.Make sure that the GPS antenna contacts are good, whether the
antenna is broken, it is recommended to be located in places with
strong signal, note that some car glass shielding film will block
3 If the test is in the room, the signal of GPS antenna in the room
will be obscured, it is recommended that the GPS antenna is placed
Q: Deviation of GPS location on map?
A: It means the signal is valid if the GPS module already
positioned, there may many reasons for the deviation, such as
government restrictions, permissible error, GPS signal
interruption, etc; the actual satellite map may have deviation for
security reasons, general map can solve the problem by using GPS
correction.3G wireless module
Q: If use the 3G wireless module for dial-up, what do I need to pay
A: 1. Choose the built-in wireless module WCDMA or EVDO,
corresponding module settings are not the same, the modules
supported by different machines models are not the same, so please
make sure whether your module and SIM is in correspondence. Do not
use telecom SIM card on WCDMA machine;
2.Check whether the settings of Server IP and port are correct,
whether 3G signal is strong enough for dialing, and then check
whether the 3G dial-up is successful or not.
3. When dialing is unsuccessful, please check 3G antenna is in good
contact or not, the dial up may fail because of weak signal,
moreover, please check whether the SIM card has enough traffic, if
no traffic, dial-up will be unsuccessful.
Q: When 3G has neither report nor video , what should be done
A: Press INFO key to enter the system information page, check
whether the SIM card exists and view the signal strength as well as
dial-up status, whether the antenna is in good contact, and then
check the SIM to see whether it is out of traffic, the most basic
judgment is to replace the SIM card. If the dial up failed with
signal, then check whether the settings of center number and the
port are correct. Moreover check whether the device number of the
product is already occupied.
Q: 3G signal is intermittent, video is jammed?
A: At present the signal coverage of WCDMA and EVDO is rather wide,
however, there are some mountainous districts without signal
coverage, and some suburban areas have weak signal due to the local
network constraints, then it will be jammed during watching of
video, or video cannot be watched at all, the greatest impact of
this situation is from the local network; Moreover check whether
the frame rate setting of sub-stream is too high, because the video
may also occur such situation when the network is poor and frame
rate setting is high.
Q: Why the vehicle and video cannot be seen in CMSviewer client
when the device has been started?
A: At first make sure the central registration server is switched
on and on the net, then check whether the host device number has
been occupied to cause conflict, secondly check whether the
settings of server-centric IP and port are correct; devices report
to the center via the built-in 3G module or via WIFI. If via
built-in 3G, please check whether selected the correct type of
built-in 3G module, for example, WCDMA and EVDO module needs the
support from corresponding SIM card, check whether the antenna is
in good contact; If it still can not report when above all are
checked, enter into the system information page to view dial-up. If
dial-up is not successful, look up whether the setting of data
access point and center number is correct. If all ultimately fail,
please collect as much information as possible to submit to the
technical supporting staff for analysis, the more data provided,
the more convenient for technicians to solve the problem.
Q: The device is online, but why can I not see the video image?
A: Please set lower sub-stream to transmit image, the blocked or
slow transmission speed situation may occur when the sub-stream
frame rate is set very high and be affected by network uploading
limit; poor network signal or intermittent will seriously affect
the video transmission.
Q: The device is properly reported on CMSviewer, but the videos
cannot be seen after using for some time?
A: Firstly check whether the host side displays dialing, if it
keeps the dialing status, it may be because the flow of the SIM
card has run out, replace the SIM card to test; Secondly query
whether the host device number has been modified by the driver, the
host with modified device number needs to be resubmitted to add
vehicle information; thirdly, if it still does not work by changing
the card, it will need to check whether the host’s 3G module fails.